|
|
|
|
|
|
|
CORNER POST SPECIALS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Last Updated
10/10/08 08:54 PM |
|
| |
--
|
 Hello to all of you from Jimmy McDonald,
Your " Local Hard Working Remodeling Guy"
at StartRemodeling.com.
--
Well, I'm a little late today in getting this out. Been fishing for Red Fish in the Gulf of Mexico and am Beat. I hope that you all will take these issues seriously and save them somewhere. Tons of time, many years of experience and the desire to help is packed in every page.
|
Some Great Hints and Tips about your ROOF!
--
 Measure your Roof from the Ground.
Use this article to help you know more about the size of you roof. Square footage is broken down into " SQUARES " which is just a term for a 100 x 100 foot area of your roof. You will find that shingles, whether they are Laminate, Cedar Shake, Metal or whatever are broken down into squares. Here's a way to measure your roof without taking the chance of breaking your back. Even us Vintage roofing guys are intimidated about some roofs. Here's some passed on knowledge for you to use!
Laminate Roofing Installation.
Most residential roofing consists of Laminate ( asphalt ) shingles. These can be purchased in 3-Tab, 25, 30 and 40 year shingles. Don't be fooled by the numbers. None of these shingles are going to withstand any type of severe weather in 12 -15 years. After 20 + years in the business, I still have NO IDEA how they come up with these numbers. However, the thicker the shingle, the more value you are going to get for your buck while they last. Not to mention that a 30 year shingle ( which I recommend for 99% of the homes I re-roof, is going to be a prettier application and save you some cash compared to the thinner 3 - Tab.
---
Here's a great article from Today's HomeOwner that I am sure you can utilize... Which roofing material is the best choice for your home? It depends on style, substance and budget. I love the way they write.
|
Paying the Bills
--  Spring is on it's way and the time to start planning for your next Home Improvement and Remodeling Project is NOW.
-
We have referred thousands of contractors to our visitors for more than 3 years now with HUGE success. We save you hours of time and hassle searching around for a Quality, Licensed and Insured Contractor.
-
We check their credit history.
-
We check their Insurance.
-
We check their references.
-
 Click on the brush and we'll send you up to 4 of these Quality companies to provide you with ideas, bids and costs on your next project, Large or Small. Receive a call in as little as 30 minutes.
|
|
Featured Project - Repairing & Maintaining Gutters
- | IMPORTANT: Read this before you start |
 Introduction Gutters are an important part of your home’s weatherproofing system. For many homeowners, their gutter system is a secondary concern and often gets neglected. Don’t make that mistake! It is important that you maintain a free-flowing gutter system as your gutters prevent rain from running from your roof and falling too close to your house. Flowing water away from your house properly will protect your foundation, keep stains from developing on your siding, and keep walkways ice-free in the wintertime. There are four basic types of gutters available – aluminum, galvanized steel, vinyl and sometimes you will find wood gutters. Galvanized steel gutters, although the least expensive, also require the most attention and maintenance. Both aluminum and vinyl gutters offer the most maintenance-free solution as they are durable and resistant to corrosion.
-- | |
To view a multimedia demonstration of this tutorial, click here .
The demonstration requires Macromedia Flash 4 player. If you don't already have it, click here to get it. | | | 1. | Leaking and Damaged Downspout. You will sometimes find that the downspout joints loosen and lose their ability to be watertight. Start by removing the screws holding the joint together or the retaining hardware depending on how yours is attached. |  |  | | 2. | Pull apart the pieces in the joint and use the wire brush to remove any existing caulk on both the outside of the male piece and the inside of the female piece of the joint. |  | | 3. | Inspect the hardware to be sure that the hardware is not in such condition that it is not reusable. Your downspout might be dented so that it cannot be used or your retaining hardware may be damaged. Replace any pieces that cannot be reused with new material. |  | | 4. | Apply caulk to the outside of the male piece of the joint, near the end, and reattach the female piece. |  | | 5. | Secure the joint with screws or other retaining hardware suitable for your gutters. |  | | 6. | Leaking gutter sections.If you find a leak at the joint, and there is no apparent damage such as rust or dents, your sealant is most likely the culprit. Try to scrape away as much of the old caulk sealant that is visible. |  | | 7. | Then, simply apply a joint caulk, such as silicone, to waterproof the joint. |  | | 8. | Leaking areas within straight gutter are usually due to rusting gutter sections. You can temporarily patch this problem, but the section will most likely need to be replaced within a couple years. To patch the rusted area, first clean the rust away using your wire brush and water. Be sure that you brush away all the rust so that you minimize the potential for the rust to spread. |  | | 9. | Use your putty knife to spread roofing cement onto the clean area and the surrounding areas. Try to keep the patch as flat as possible so that water will run down your gutter properly. If your rusted area is very large or you want to make a more permanent fix, you should replace the entire gutter section or cut out the damaged section and replace it. |  | | 10. | Replacing a damaged gutter section.There are times when you will have to remove and replace sections of your gutter system that have been damaged by rust or falling debris such as tree branches or ice. Before replacing sections of gutter that are sagging, be sure that it is your gutter, and not the gutter support, which has failed. You should first remove any retaining hardware from the section of gutter that you need to replace. As shown, remove the retainers and connectors. |  | | 11. | Use a 4x4 block of wood and place it inside the good section of gutter as you cut the bad section out with a hacksaw. This will keep your gutter in good shape while you are cutting and prevent the gutter from twisting as you cut it. |  | | 12. | Cut out a section of gutter to replace the piece you have cut out of the existing gutter. Cut the replacement section about 2” longer than the section that is being replaced to allow for some overlap. |  | | 13. | Using your caulk gun, apply roofing cement to the inside of the original gutter and place the new section into place so that it overlaps about an inch on each side. |  | | 14. | Drill holes appropriate to your rivets into the overlapping sections of the gutter, and securely fasten the sections together with rivets. |  | | 15. | Replace any retaining hardware that you originally removed, so that the gutter stays in place. |  |
|
|
|
IMPORTANT INFORMATION Because working conditions, safety issues, tools, equipment and skills of the individual can vary greatly, Easy2.com assumes no responsibility for any damages, injuries or losses that occur as a result of using the information provided by Easy2.com's instructional services. Do not use Easy2 tutorials as a substitute for carefully reviewing and understanding the instructions or manuals that accompany products, tools and equipment that are used in a project. Make sure to check with the local building department to ensure compliance with codes and regulations related to your project. You should always consult a trained professional with any questions about your specific project's needs or safety concerns. Always know your own limitations and factor in your own good judgment and common sense. Your use of this tutorial constitutes your acceptance of terms conveyed in Easy2.com's Terms of Use and Copyright Policy. YOUR SAFETY Before you begin a project, make sure you plan ahead and anticipate any safety issues. Following are some important safety tips that can apply to most projects. Since every project is different, do not consider this a comprehensive list of all the safety issues that you may need to address. General Safety - Do not attempt a potentially dangerous project when you are tired, irritated, sick or under the influence of drugs or alcohol.
- Wear approved eye protection when working with power tools or striking tools such as hammers.
- When working in dusty situations, wear a dust filter mask over your mouth and nose.
- Make sure you check building codes for your area before planning construction projects.
- Keep all blades, bits and other cutting parts sharp on both power tools and hand tools. Dull tools can require you to apply extra force, which can lead to injuries.
- Make sure you have a safe work environment that is well lit and free from obstructions and interference from clothing, long hair and jewelry.
- Turn off breakers or remove fuses when working on all electrical projects.
Power Tools - Read the instructions thoroughly and make sure you understand proper operation and safety issues related to each tool. Use a tool only for its intended application. Make sure you know each tool's limitations.
- If a tool requires grounding, make sure it is properly grounded. Do not use 2-prong adapters.
- Unplug saws, drills, routers and other power tools when changing or installing blades, bits and other attachments.
- Keep your hands safely away from blades, bits and moving parts as you operate a power tool.
Paints & Chemicals - Heed all product warning labels! Make sure you have adequate ventilation for flammable and noxious chemicals. When using flammable materials, shut off pilot lights on furnaces, hot water tanks and stoves.
Ladders & Scaffolds - Make sure stepladders are completely opened and positioned with all four legs firmly stabilized and supported. Never stand on the top platform of a stepladder.
- When using an extension ladder, firmly plant both side rails on solid ground. Do not put the base of the ladder too close or too far from the vertical surface it is propped against. Your weight should be positioned between the base of the ladder and vertical surface.
- Make sure that all legs of a scaffold are firmly planted on solid ground. Use blocks of wood on softer ground to provide better support. Always stand on platforms in between the supports that hold it up.
|
That's it for this month's Hint's, Tips and Tricks eZine.
We hope you enjoyed the new format and look forward to seeing you
on the site. Have a GREAT DAY! from everyone at StartRemodeling.com |
|
|
To unsubscribe... click here and type remove in the subject line!
Please make sure to reply with the email address
that this newsletter was delivered to. Thank You.
| |
|
| |
|
Be sure to take proper precautions when working in high areas.
